Resetter Canon BJC-1000/BJC-2000/BJC-2100 and BJC Series

Canon BJC 1000

1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Canon BJC-2000/BJC-2100

1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Read more Resetter Canon BJC Series after jump



Canon BJC-210/BJC-240/BJC-250/BJC-255/BJC-265/
BJC-4100/BJC-4200/BJC-4300/BJC-4400/BJC-4550/BJC-4650

1.Unplug Power Cord
2.Hold POWER and RESUME buttons
3.Plug in Power Cord
4.Release buttons Open front door of printer
5.Hold the CARTRIDGE and RESUME buttons
6.Press POWER
7.Release all buttons after the beeps
8.Press CARTRIDGE once
9.Press RESUME


Canon BJC-5000

1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data

Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print

Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.

Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.


Canon BJC-5100

Self Test
Switch Printer off. Hold Power for 1 beep.

Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data

Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print

Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.

Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.


Canon BJC-3000/BJC-6000/BJC-6100/BJC-6200/S400/S450/F300/F600/F620
Canon BJC-7000/BJC-7100/BJC-8000/BJ-F800/i6500

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data


Canon BJC-600/BJC-600e/BJC-610/BJC-620

1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps


Canon BJC-50/BJC-55/BJC-80/BJC-85/M40/M70

1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord


Canon BJ-30/BJC-35v/BJC-70

F14 Error Reset

1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer


Canon BJ F900/F890/F700/F500/S900/S820/S750/S520

Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.

Use all method with own risk , i'll try some but not off all.

Read More

Resetter Canon S9000/S300/S400/ i550/ i560/ i850/ i860/ i865/ i9100/ i9950/PIXMA iP3000

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.


Canon S900, S820, S750, S520

1. Turn off the printer.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
4. The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.
5. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function.The lamp will alternate color with each key press

1. Service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
6. After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.


Canon S9000

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Read More

Resetter Canon i850/i950/S600/S6300/S450

Canon Canon i850, i950, S600

Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function

Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter


Canon S6300

1.Power off printer
2.Hold RESUME button then press and hold POWER button.
3.Hold POWER and Relase RESUME
4.Pres RESUME twice then relase both POWER and RESUME buttons
5.When the indicator lights stedy,press RESUME 4 times
6.Press power to set data
7.Print again

Read more after jump



Canon S450

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
7: Press Power to set data

Read More

Resetter Canon MPC190/MP145/MP150/MP160

Canon MPC190

Reset Waste Ink

1) Enter SERVICE MODE.
By pressing Menu, Copy, Scan, Copy, Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Canon MP145

With the printer powered off but connected to a power source , you must:

A) Press stop/reset button, and then press [ON/OFF] button to restart
B) Press [ON/OFF] again and then press twice the stop/reset button.
C) Press [ON/OFF] & Stop/reset button together, this time to enter the repair status and power lights will be green,
D) Press stop/reset button 4x and warning lights will be go out in [ON/OFF]button.
E) Turn off the printer.( it must be turn off) and then turn it on again.

Use with your own risk , i'll try this way and my Pixma MP145 not blink again.

Read more after jump

Canon MP150

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset
5 Turn off the printer.( it must be turn off)and then turn it on again.


CANON PIXMA MP160

1) With the printer off, but connected, press the On / Off button, while the Stop button / Reset. (The triangle inside the circle)
2) When the light of On / Off switch is (green), and press the release button Stop / Reset twice
while held down the On / Off button (Power).
3) Release the buttons On / Off and Stop / Reset (regardless of order), Wait for the menu is ready)
4) When the light of On / Off this green, press the Stop / Reset 4 times
5) Turn off the printer (press three times On / Off)
6) Enjoy it ...

Read More

Resetter Canon IP 4200

Canon ip4200
Reset Options:

1. With the printer power turned off, while pressing the Resume/Cancel button, press and hold the Power button. (DO NOT release the buttons. The Power LED lights in green to indicate that a function is selectable.)

2. While holding the Power button, release the resume/Cancel button. (DO NOT release the Power button.)

3. While holding the Power button, press the Resume/Cancel button 2 times, and then release both the Power and Resume/Cancel buttons. (Each time the
Resume/Cancel button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.)

4. When the Power LED lights in green, press the Resume/Cancel button the specified number of time(s)setting).

Read more after jump


Time(s) LED indication Function Remarks
0 times Green (Power) Power off When the print head is not installed, the carriage returns and locks in the home position capped.
1 time Orange (Alarm) Service test print .
2 times Green (Power) EEPROM information print
3 times Orange (Alarm) EEPROM initialization
4 times Green (Power) Waste ink counter resetting
5 times Orange (Alarm) Destination settings After entering the destination settings mode, press the Resume/Cancel button the specified number of time(s) to select the destination.
6 times Green (Power) Print head deep cleaning (Cleaning of both black and color)
7 times Orange (Alarm) Reserved
8 times Green (Power) CD / DVD check pattern
9 times Orange (Alarm) CD / DVD print position correction (horizontal: X direction)
10 times Green (Power) CD / DVD print position correction (vertical: Y direction)
11 to 13 times Orange, Green, Orange(Alarm,Power,Alarm) Return to the menu selection
14 times Green (Power) Left margin correction Not used in servicing.
15 times Orange (Alarm) Return to the menu selection

Time(s) LED indication Destination CD / DVD print
0 times Green (Power) No change of the destination
1 time Orange (Alarm) Japan Supported
2 times Green (Power) Korea Not supported
3 times Orange (Alarm) US Not supported
4 times Green (Power) Europe Supported
5 times Orange (Alarm) Australia Supported

Use with your own risk

Read More

Resetter Canon Printer (2)

Canon PIXMA iP1000

Waste Ink Counter Reset.

Step 1: Manual for Service mode

1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2. Open General Tools software and select(USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"


Read more after jump


Canon PIXMA iP1500

Waste Ink Counter Reset.

Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2. Open General Tools software and select(USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

Use with your own risk

Read More

Resetter Canon IP 3300

Canon IP 3300 Manual resetter

EERPSOM Reset Procedure

Try to enter service mode and reset EEPROM:

1. Start with the printer OFF
2. Hold down RESUME and then hold down POWER
3. release RESUME
4. press RESUME twice, then release POWER
5. Let green light blink until printer is done moving print head.

Now you should be in service mode.

6. Press RESUME 1 time then POWER to execute the command
This will print head test print. Just if you want to check clogging problems in depth.

7.Press RESUME 2 times then POWER to execute the command
This will print EEPROM information ink usage etc.

8. Press RESUME 3 times then POWER to execute the command
This will reinitialize (reset) EEPROM

9. Press RESUME 2 times then POWER to execute the command
This will print EEPROM information once more, you should compare it with your fist print. All zeroes should be all over the place.
That means your EEPROM is reset.

Use with your own risk

Read More

Resetter Canon Printer (1)

Here i share how to reset your printer if its blinking , use with your own risk
Canon Waste Ink Tank Reset Procedures

Canon GENERIC "S" SERIES RESET CODE

(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2)
more times in succession. Note: you are still holding the POWER button). The printer's
carriage will "reset" or move momentarily. If the above was properly performed the
printer will enter the "Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter
function. The lamp will alternate (change) color with each key press.
a. Service/Factory test printout, including ink sensor check.
b. EEPROM - Info printout.
c. EEPROM - Initialization.
d. Reset the Waste ink counter.
e. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)

After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the
printer.

Read more after Jump


Canon i320, i255

Waste Ink Counter Reset.

Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2. Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark "After service mode Pls use software for permanent reset"

Read More